Ingen varer
Priserne er inklusiv moms
Varen er nu lagt i din kurv
Der er 0 varer i din kurv Der er 1 vare i din kurv
Mindre, lettere og bedre end nogensinde før, vores Revo Micro HotEnd bruger den mindste heatsink, vi har produceret hidtil. Med en vægt på kun 30 g, brug Revo Micro til at presse mere hastighedsydelse fra dit bevægelsessystem. Revo Micro, der kan tilpasses til Bowden- eller direkte drevopsætninger, er fuldt ud kompatibel med vores Revo-økosystem, så du nemt kan skifte dyser uden værktøj eller varmspænding ved stuetemperatur ved kun at bruge fingrene. Med en anodiseret sort køleplade kører Revo Micro ikke kun køligt – det ser også cool ud.
- Designet til brug med Revo dyser
- Fungerer med en Revo HeaterCore for hurtigere opvarmning
- Den mindste og letteste HotEnd, vi har produceret hidtil
- Titanium-lignende ydeevne
- Ultralet konstruktion for forbedret hastighedsydelse
- Kompatibel med populære 3D-printere inklusive Creality, Ender, Prusa, Anet, Biqu, Monoprice og mange flere
På Fjernlager
27688
Titanium-like performance. Our special manufacturing process gives this aluminium HotEnd the strength and low thermal conductivity of titanium, without actually being titanium!
Ready for Revo. Change nozzles at room temperature using just your fingers. No complex tools, no hot tightening. Revo Nozzles are a factory sealed nozzle and heatbreak in one, so they’re easy to fit and can’t leak material when in use.
New hotness. A Revo HeaterCore heats up in seconds. It’s much safer too – unlike other solutions on the market, a positive temperature coefficient (PTC) means the Revo HeaterCore can not melt at extreme temperatures: power reduces as it gets hotter, so hazards are reduced in the event of a thermal runaway.
Runs cool, looks cool. With an anodised black heatsink, not only does Revo Micro run cool – it looks cool, too.
Flexible to any setup. Revo Micro plays nice with Bowden and direct drive setups, but its lightweight construction makes it an ideal choice for Bowden setups.
Please note:
- This kit does not include any 3D printed mounts
- The Revo Micro fan must be connected using the 5V regulator unless connecting directly to a 5V pin
- This kit comes with 100mm of PTFE tube
- You may need to adjust your Z offset when changing nozzles.
Key features:
- Max temp: 300C
- Weight: 30g
- Nozzle type: RapidChange Revo
- Maximum temp: 300°C
- M12 x 1.5 thread mounting
- Compatible with Bowden and direct drive systems
Kit includes:
- 1 x Revo Micro heatsink
- 1 x M12 x 1.5 nut
- 1 x 20 x 20 x 10 5V fan
- 1 x 12V or 24V to 5V regulator board
- 1 x Revo Micro fan duct
- 1 x Collet
- 1 x Collet clip
- 1 x Revo HeaterCore 12V or 24V
- 1 x Revo HeaterCore spring
- 1 x Extension cable kit
- 1 x 100mm PTFE
Single nozzle kit:
- 1 x 0.40mm brass Revo Nozzle
Fully loaded nozzle kit:
- 1 x 0.25, 0.40, 0.60, and 0.80mm brass Revo Nozzles
Documentation:
