0
Vare:
Varer:
(tom)
Ingen varer
Fastlægges senere
Forsendelse
0,00 DKK
Moms
0,00 DKK
I alt
Priserne er inklusiv moms
Varen er nu lagt i din kurv
Antal
I alt
Der er 0 varer i din kurv Der er 1 vare i din kurv
Varer i alt
(inkl. moms)
Forsendelse i alt (inkl. moms)
Fastlægges senere
Moms:
0,00 DKK
I alt
(inkl. moms)
Bondtech opgraderingssæt til Wanhao I3.
Dette sæt giver et højtydende materialefremføringssystem med mulighed for at printe hurtigere med forbedret kvalitet. Den justerbare fingerskrue giver dig mulighed for at finjustere kraften, der virker på filamentet.
Husdelene er professionelt SLS-trykt i nylon for maksimal styrke og præcision.
Ikke på lager
21567
Få besked når varen er på lager
Skriv din e-mail-adresse her, hvis du vil have besked når vi igen har denne vare på lager:
Jeg ønsker en e-mail når varen kommer på lager
Skriv bedømmelse
Bondtech Mini with Dual-Drive gears that grips the filament from both sides without any slippage or grinding as an upgrade kit for the Wanhao I3 printer.
The smaller effective diameter of the drivegear will increase the torque by about 50% and also the resolution will increase with 50% since the E-step value is 140 compared with the 96 as the standard extruder.
The filament path is fully guided and this makes the extruder work perfect with both hard and soft filaments, the drive gear is also in hardened steel to withstand wear from especially filaments with abrasive additives like carbonfiber and glassfiber.
The quick-release lever lets you load and unload filament with ease for quick filament changes.
Spring loaded pre-tension on the filament.
This kit uses the original steppermotor that came with the printer and is installed in 1h.
Step-by-step guide is supplied
The kit consists of the following:
Extruder parts in nylon with thread inserts.
Hardened drivegears in steel.
Needlebearings
Harded ground shaft.
Bolts M3x45 mm
Shim in alu.
The original metal plate that holds the extruder needs to be modified in order to give room for the extruder, this is easily done with a hacksaw and a file.
Maximum X-movement is restricted about 15 mm on the right side.
E-step needs to be adjusted to 140 step/mm (with the LCD panel)
Weight: 62g
The smaller effective diameter of the drivegear will increase the torque by about 50% and also the resolution will increase with 50% since the E-step value is 140 compared with the 96 as the standard extruder.
The filament path is fully guided and this makes the extruder work perfect with both hard and soft filaments, the drive gear is also in hardened steel to withstand wear from especially filaments with abrasive additives like carbonfiber and glassfiber.
The quick-release lever lets you load and unload filament with ease for quick filament changes.
Spring loaded pre-tension on the filament.
This kit uses the original steppermotor that came with the printer and is installed in 1h.
Step-by-step guide is supplied
The kit consists of the following:
Extruder parts in nylon with thread inserts.
Hardened drivegears in steel.
Needlebearings
Harded ground shaft.
Bolts M3x45 mm
Shim in alu.
The original metal plate that holds the extruder needs to be modified in order to give room for the extruder, this is easily done with a hacksaw and a file.
Maximum X-movement is restricted about 15 mm on the right side.
E-step needs to be adjusted to 140 step/mm (with the LCD panel)
Weight: 62g
Bondtech / Bondtech / Bondtech / Bondtech / Bondtech / Bondtech / Bondtech / Bondtech / Bondtech / Bondtech / Bondtech / Bondtech / Bondtech /
